sFc-601 multi-purpose stainless steel electrolytic polishing liquid one, characterized by a high polishing efficiency, within a few minutes can be polished to a mirror-bright, strong and polishing depth, gloss retention after polishing the long term. 2, the temperature of the polishing solution used, low cost, compared with the conventional polishing liquid commonly used lower than 30%. 3, polishing current density, low voltage, the use of low temperature, low power consumption compared to the traditional process about 1 times. 4, easy maintenance and management of the slurry stability. 5, for austenitic, martensitic, ferritic stainless steel electrolytic polishing. 6, the product does not contain recipes classic environmental hexavalent chromium, cyanide. Second, the polishing liquid composition and operating conditions: the inorganic acids, proprietary additive, water Temperature: 10-90 ℃ 60-80 ℃ optimal anodic current density: DA 20-60A / dm2 best 20-40A / dm2 voltage: 5-8 volt Polishing time: 3-5 minutes cathode material: a lead or lead alloy, stainless steel cathode area: 2-3:1 three anode area, slotted step ⒈SFC-601 agent stock solution using electrolytic polishing, electrolytic polishing, in its initial use will produce large amounts of foam, so the distance between the top of polishing and polishing fluid level should be between the slots ≤20cm. After power after notching ⒉ used directly, without the power aging. Fourth, the process efficient degreaser degreasing → water washing → pickling → electrolytic polishing → three countercurrent washing (→ passivation → water →) in hot water and → → dry or drying five, bath maintenance and supplemented with a stainless steel workpiece before entering the polishing tank should be left in the water as much as possible to remove the workpiece surface, due to excessive moisture entrained workpiece polished surface may cause severe pitting, local erosion caused workpiece scrapped. 2, in the electrolytic polishing process, the workpiece as the anode of stainless steel, which contains iron, chromium, nickel element is changing without the dissolved metal ion is deposited on the cathode surface within the slurry. As the polishing process, the metal ion concentration increased, when a certain value, these metal ions to the phosphate and sulfate forms that have precipitated from the polishing liquid, polishing the bottom of settling tank. To this end, the polishing liquid must be regularly filtered to remove the solid precipitates, as the case may be using residues machine. 3, in the process of polishing tank run, in addition to inorganic acids continue to consume external moisture loss due to evaporation and electrolysis, in addition, high-viscosity slurry entrainment losses workpiece surface polishing liquid declining need regular polishing tank to fill with fresh polish solution and water. 4, the proportion of pre-polishing liquid raw unpolished 1.65, in the process of polishing tank runs, the proportion of slurry should be controlled within the range of 1.65 ± 0.1. Polishing liquid specific gravity and viscosity is too high, indicating that the polishing liquid moisture content of less than high or low content of phosphoric acid; Conversely, the proportion of low polishing fluid, indicating that the polishing liquid water content is too high. Often measured with a polishing liquid specific gravity hydrometer is a simple and effective means of control. 5, in the case of a conditional, the best regular analysis of the content of slurry acidity, inorganic acids. Sixth, the device typically require electrolytic polishing is a mineral acid, and operate at higher temperatures, hence the polishing tank, clean tank, a cathode, heating the material to be manufactured from corrosion-resistant coil polishing liquid filter device and exhaust means. 1, polyethylene, polypropylene, polyvinyl chloride, epoxy fiberglass and steel tanks lined with these materials can be used as electrolytic polishing tank. 2, electric heating or steam heating coil can be used the following materials: ⑴, PTFE coil: Teflon tube bundle heat exchanger for steam heating. Electrically heated Teflon tube for electrical heating. PTFE coil prices may be high but the long life and electrically. ⑵, pure lead or lead-antimony alloy coil: pure lead or lead-antimony alloy used as electrolytic polishing steam heating coils. To increase the life of the coil, the polishing fluid level should be at the junction with the air thick with the other lead. ⑶, quartz electric heating tube. 3, linked with: copper with the longest life outside coated titanium hooks to hang with the sol. Because of the polishing liquid does not contain chromic acid, can also be used as a phosphor bronze hooks. 4, filtration and cleaning plant: Cleaner filter and non-necessities, which is suitable for uninterrupted continuous production of high degree of automation in the large-scale production lines. Seven, packaging, transport and storage 35 kg reinforced plastic drum, in accordance with the general chemical transport, storage and shade can be. Eight, about 420 blades mountain a few experiences, new slotted electrical throw should be taken two days before hanging up to speed over the water to avoid corrosion. 2, increase concentration and prolonged soaking time lye corrosion products for help. 3, electric throw before cleaning quality product quality and syrup life electrolytic some impact. 4, long-term power complex products with a stainless steel cathode may be more favorable. 5, complex production linked with the auxiliary cathode design is very important, says there are seven hanging thirds of syrup. Electric throw consulting and service hotline: 13428621272 Pang workers